CalculateImpositionInput
Input for calculating imposition layout. Finished size, bleed, page count, quantity, and grain direction are read from the component.
Fields
Component to calculate imposition for
Layout mode: signature, ganging, or web (default signature)
Possible values (3)
SIGNATUREFolded signatures for books/brochures
GANGINGN-up step-and-repeat for flatwork
WEBWeb press imposition (roll-fed)
Explicit calibrated or measured single-fold shingling. Requires LEFT binding, f4-only folds and substrate caliper; omission preserves uncompensated behaviour.
Binding side of the upright reader page. Constrains signature geometry and artwork orientation; omitted preserves legacy fitting.
Possible values (3)
LEFTLeft edge of the upright reader page
RIGHTRight edge of the upright reader page
TOPTop edge of the upright reader page
Binding type that determines page ordering (saddleStitch, perfectBound, etc.)
Possible values (7)
SADDLE_STITCHSaddle stitch: all sheets nest inside each other
PERFECT_BOUNDPerfect binding: gathered signatures glued at spine
CASE_BOUNDCase binding: sewn or glued signatures in hard cover
WIRE_BOUNDWire binding: pages bound with wire spiral or comb
FLATWORKFlatwork: no binding, step-and-repeat
FOLDEDSingle fold, no gathering or binding
OTHEROther or unspecified binding method
Explicit substrate IDs to consider (overrides component substrate)
Executable anonymous signature candidates, 1 through 64; mutually exclusive with permittedFolds. Omitted binding defaults to folded; flatwork/other are invalid with candidates.
Fold pattern IDs to allow, e.g. ["f8", "f16", "f32"]. Nil = all.
Maximum pages-up cap
Preferred imposition scheme
Possible values (5)
WORK_AND_TURNWork-and-turn (both sides from same plate, sheet flipped on long edge)
WORK_AND_TUMBLEWork-and-tumble (both sides from same plate, sheet flipped on short edge)
SHEETWISESheetwise / work-and-back (separate plates for each side)
WEB_PERFECTWeb perfecting (both sides printed inline)
OTHEROther scheme
Horizontal gutter in mm (default 0)
Vertical gutter in mm (default 0)
Gripper margin in mm (default 10)
Tail margin in mm (default 5)
Side margins in mm (default 5)
Explicit row count for ganging (nil = auto)
Explicit column count for ganging (nil = auto)
Web press profile (required for web mode)
Preference for fewer blank page positions among candidate plans (default 1.0). This is not a maximum waste limit.
Objective weight for sheet utilisation (default 1.0)
Objective weight for signature count (default 0.5)
Objective weight for fold uniformity (default 0.3)
Override auto-selection and pick a specific plan by index
Delete existing ImpositionSpec records before writing (default true)
Exact type SDL
"""
Input for calculating imposition layout. Finished size, bleed, page count, quantity, and grain direction are read from the component.
"""
input CalculateImpositionInput {
"""Component to calculate imposition for"""
componentId: ComponentID!
"""Layout mode: signature, ganging, or web (default signature)"""
mode: ImposingMode
"""
Explicit calibrated or measured single-fold shingling. Requires LEFT binding, f4-only folds and substrate caliper; omission preserves uncompensated behaviour.
"""
creep: BookCreepInput
"""
Binding side of the upright reader page. Constrains signature geometry and artwork orientation; omitted preserves legacy fitting.
"""
bindingSide: BindingSide
"""
Binding type that determines page ordering (saddleStitch, perfectBound, etc.)
"""
bindingType: BindingType
"""Explicit substrate IDs to consider (overrides component substrate)"""
substrateIds: [String!]
"""
Executable anonymous signature candidates, 1 through 64; mutually exclusive with permittedFolds. Omitted binding defaults to folded; flatwork/other are invalid with candidates.
"""
foldCandidates: [FoldCandidateInput!]
"""Fold pattern IDs to allow, e.g. ["f8", "f16", "f32"]. Nil = all."""
permittedFolds: [String!]
"""Maximum pages-up cap"""
maxPagesUp: Int
"""Preferred imposition scheme"""
scheme: ImpositionScheme
"""Horizontal gutter in mm (default 0)"""
gutterH: LengthInput
"""Vertical gutter in mm (default 0)"""
gutterV: LengthInput
"""Gripper margin in mm (default 10)"""
gripEdge: LengthInput
"""Tail margin in mm (default 5)"""
tailEdge: LengthInput
"""Side margins in mm (default 5)"""
sideMargin: LengthInput
"""Explicit row count for ganging (nil = auto)"""
gangingRows: Int
"""Explicit column count for ganging (nil = auto)"""
gangingCols: Int
"""Web press profile (required for web mode)"""
webPressProfile: WebPressProfileInput
"""
Preference for fewer blank page positions among candidate plans (default 1.0). This is not a maximum waste limit.
"""
wasteWeight: Float
"""Objective weight for sheet utilisation (default 1.0)"""
utilisationWeight: Float
"""Objective weight for signature count (default 0.5)"""
sigCountWeight: Float
"""Objective weight for fold uniformity (default 0.3)"""
foldUniformityWeight: Float
"""Override auto-selection and pick a specific plan by index"""
selectPlanIndex: Int
"""Delete existing ImpositionSpec records before writing (default true)"""
replaceExisting: Boolean
}