TemplateOperationSpecInput
Input for an operation step within a product template
Fields
Stable local identifier
Component this operation belongs to
Operation kind
Possible values (50)
BINDINGHolding the finished components together as one product. The generic kind, for when the specific binding method is not yet decided.
BOOK_BLOCK_MAKINGAssembling the folded signatures into the book block that will later be cased in.
COLLATINGGathering printed sheets or signatures into the correct page order before binding.
COMB_BINDINGBinding with a plastic comb through punched rectangular holes, so the book opens flat and can be reopened to add pages.
CONTOUR_CUTTINGCutting along an arbitrary outline that follows the artwork, rather than to a rectangular trim.
CREASINGPressing a channel into the substrate so it folds along a controlled line without cracking the fibres or the printed surface.
CUTTINGTrimming the sheet to its finished size on a guillotine or three-knife trimmer.
DEBOSSINGPressing a design below the surface of the substrate, the inverse of embossing.
DIE_CUTTINGCutting shapes with a steel die, for outlines a straight guillotine cut cannot make.
DIGITAL_PRINTINGPrinting directly from digital data with no plate, so each impression can differ and short runs carry no plate cost.
DRILLINGMaking round holes through the stack, typically for ring or mechanical binding.
EMBOSSINGRaising a design above the surface of the substrate under heat and pressure.
FOIL_STAMPINGApplying metallic or pigmented foil to the substrate with a heated die.
FOLDINGFolding the printed sheet into signatures or into the finished product's fold pattern.
GLUINGApplying adhesive to join parts of the product, as in a carton seam or a bound spine.
HEAD_BANDINGAttaching the decorative fabric band at the head and tail of a hard-bound book's spine.
INKJET_PRINTINGPrinting by jetting ink droplets onto the substrate, without contact between head and stock.
FLOOD_COATINGApplying a coating over the entire printed area, for protection or overall finish.
LAMINATINGBonding a film over the printed sheet to protect it and change its surface finish.
OFFSET_PRINTINGLithographic printing in which ink passes from plate to blanket to substrate. The high-volume commercial process, with a per-job plate cost.
PACKINGPacking the finished product for storage or despatch.
PERFECT_BINDINGBinding by milling the spine flat and gluing the pages into a wrapped cover, as used for paperbacks.
PERFORATINGCutting a line of small slits so a part can be torn away cleanly by hand.
PRECUTTINGCutting the stock down before printing, to bring it to press size or to split it into working sections.
PRINTINGMarking the substrate with the artwork, when the specific press process is not yet decided.
PUNCHINGMaking shaped holes with a punch tool, for binding elements or for the product's own features.
RING_BINDINGBinding with wire loops through punched holes, so the book opens flat and lies open.
SADDLE_STITCHINGStapling folded signatures through the spine fold. Cheap and fast, but limited to low page counts.
SCORINGImpressing a line to weaken the substrate along a fold, without cutting it.
SEWINGSewing the signatures together with thread, the most durable binding for a book block.
REWINDINGRewinding printed web into delivery rolls with authored count, length and winding requirements.
SLITTINGCutting the web or sheet lengthwise into narrower strips.
SPIRAL_BINDINGBinding with a continuous coil threaded through punched holes.
STITCHINGFastening with wire staples, when the stitching pattern is not specified further.
STRIP_BINDINGBinding with a plastic strip clamped through the punched edge of the stack.
CASE_MAKINGMaking the hard case — boards plus covering material — that a book block is later cased into.
CASING_INFixing the finished book block into its case to complete a hard-bound book.
CUSTOMAn operation the print catalog does not name. Its meaning comes from the operation's own parameters rather than from this kind.
DRYINGAllowing or forcing ink or coating to cure before the next operation can run. Occupies time and space without changing the product.
ENDPAPER_TIPPINGGluing the endpapers to the first and last signatures of a book block.
EYELETSSetting metal eyelets into punched holes, to reinforce them for hanging or lacing.
HEMMINGFolding and securing the edge of a flexible substrate so it will not fray.
PLATEMAKINGImaging the printing plates from the prepared artwork, before the press can run.
ROUNDING_BACKINGShaping a book block's spine into a curve and flaring its shoulders so the case fits and the book opens properly.
SPINE_MILLINGMilling the folded spine off the book block to expose the individual leaves for adhesive binding.
SPOT_VARNISHApplying varnish to selected areas only, to contrast finish against the uncoated areas around them.
KISS_CUTTINGCutting through the face stock of a self-adhesive material but not its liner, so the label lifts off intact.
REVERSE_CUTTINGCutting from the reverse of the sheet, for products viewed through the substrate.
PARTIAL_CUTTINGCutting part-way through the substrate's thickness rather than all the way through.
WHITE_UNDERPRINTLaying white ink beneath the artwork so colours stay opaque on a clear, metallic, or dark substrate.
Display name
Default parameters as JSON string
Local IDs of predecessor operations
Referenced by (3)
Exact type SDL
"""Input for an operation step within a product template"""
input TemplateOperationSpecInput {
"""Stable local identifier"""
localId: String!
"""Component this operation belongs to"""
componentLocalId: String
"""Operation kind"""
kind: OperationKind!
"""Display name"""
name: String!
"""Default parameters as JSON string"""
defaultParameters: String
"""Local IDs of predecessor operations"""
dependsOn: [String!]!
}